Fabrication
Physical countertop templating: how to build a strip template that fits
How to template countertops with luan strips and hot glue: tools, step-by-step build, marking, curves and bowed walls, accuracy, and when it still beats digital.
, CEO, Stonify
A physical template is a full-size pattern of each countertop piece, built on the installed cabinets from thin strips of luan plywood, MDF or plastic hot-glued into a rigid frame. The templater follows the real walls, sets the overhangs, and marks every finished edge, seam, sink centerline and cutout on the strips. The shop then traces it onto the slab or digitizes it for the CNC. A careful strip template holds about 1/16 inch. It costs $20 to $50 in materials per kitchen, needs no batteries or software, and takes about 45 to 90 minutes for a standard kitchen. Compared with digital templating, it is slower on site, bulkier to carry and store, and needs an extra step before the CNC can use it.
What a physical template is, and why shops still use it
Stone cannot be trimmed on site the way wood or laminate can. The piece has to arrive already the right shape, and kitchens are never the neat rectangles on the plan. Walls bow, corners come in at 88 or 92 degrees, and cabinets stick out a little further at one end than the other. A template is how the shop captures that real shape.
A physical template (also called a stick template, strip template or luan template) captures it with a full-size pattern. Luan (also spelled lauan) is thin plywood, about 1/8 inch or 3mm, sold in 4 × 8 ft sheets as door skin. Ripped into strips, it is stiff lengthwise, light, easy to cut with a utility knife, and it takes hot glue well.
Digital devices now do most templating in larger shops. They capture the room as points and produce a CAD file that goes straight to the CNC. See digital templating. Physical templating remains common, and it is worth doing well, because:
Equipment costs almost nothing, which matters for small shops and new templaters.
There is nothing to calibrate, charge or crash. Many digital shops keep a strip kit in every truck as a backup.
It works in cramped spaces where a device has no line of sight, such as under upper cabinets, in closets and in tight bathrooms.
A template laid on the actual slab shows exactly which part of the stone each piece gets. That makes it a useful layout tool on veined natural stone, even in digital shops.
For materials finished by hand on site, such as butcher block and some solid surface, a strip template is often all the job needs.
Tools and materials
Item | What it is for |
|---|---|
Luan strips, 1/8 in, ripped 1-1/2 to 2 in wide | Main frame. Narrower strips flex too much on long runs. Wider strips are heavy and waste material. |
Narrow strips, 1/2 to 3/4 in | Bending around curves |
A few 1/4 in strips, or MDF | Stiff front-edge reference and long spans over about 8 ft |
Luan or hardboard sheet offcuts | Solid infill for curves, corners and cutout areas |
Hot glue gun, spare gun, plenty of sticks | Joints. A cordless gun avoids hunting for outlets. |
Utility knife, small handsaw or snips | Cutting strips to length and to angle |
25 ft tape, framing square, combination square | Measuring and checking square |
Digital angle finder | Reading non-90-degree corners to a tenth of a degree |
Scribe or compass | Transferring a bowed wall onto a strip |
Level (2 or 4 ft) and a torpedo level | Checking cabinets before you start |
Overhang gauge block | A block cut to the shop's standard overhang (for example 1-1/2 in) so the front strip goes on the same everywhere |
Fine permanent markers in two colors | Marking lines and notes |
Manufacturer cutout templates and spec sheets | Sinks, cooktops, faucets |
Phone or tablet camera | Photos of every corner, cutout and note |
Materials for a full kitchen usually come to two or three sheets of luan plus glue, about $20 to $50.
Before you start: is the job ready?
A template is only as good as the cabinets under it. Templating on cabinets that later move, or with a sink that later changes, produces a perfect template of the wrong kitchen. Before any strips go down, confirm:
Base cabinets are installed, fastened to the wall and to each other, and level. Most shops want them within about 1/8 inch over 10 feet. Note any shims.
Any plywood subtop is installed, since it changes the counter height and sometimes the overhang reference.
The sink is on site, or its exact model is confirmed with a cutout template. The same goes for the faucet (number of holes), cooktop or slide-in range, and any soap dispenser, air gap or pot filler.
Old tops are off, unless the shop has agreed to template around them.
The customer or contractor is there to decide overhangs, seams and edges.
If the answer to any of these is no, call the office before building anything. A return trip costs less than a recut.
How to build a strip template, step by step
Walk the job with the customer. Confirm the overhang on every exposed edge, which edges get the profile, the sink type and reveal, the faucet hole count and spacing, the backsplash height, and where seams can and cannot go. Write the answers on the first strip you lay, so they travel with the template.
Check the cabinets and walls. Put a level on each run. Hold a framing square in every inside corner. For a long corner, use a 3-4-5 check: mark 3 ft on one wall and 4 ft on the other, and the diagonal between the marks should be exactly 5 ft. A short diagonal means the corner is tight (under 90 degrees). A long diagonal means it is open.
Lay the wall strips first. Set a strip on the cabinet deck tight against each back wall and side wall. Let it follow the wall. If the wall bows enough that a straight strip would leave a gap wider than the shop's caulk standard (many shops aim for about 1/8 inch), scribe the strip to the wall so the stone follows the bow. Template to the actual wall. The shop applies its own install clearance, so don't guess one unless the shop's rule tells you to.
Set the front edge. Run a strip along the cabinet faces, pushed out by the agreed overhang. Use the gauge block every couple of feet so the overhang is the same along the run. Check it at both ends and the middle, because cabinet fronts are not always straight either.
Tie the frame together. Glue cross-pieces between the wall strip and the front strip every 12 to 18 inches, like the rungs of a ladder. Add a diagonal brace on any piece wider than about 36 inches so it cannot rack into a parallelogram when lifted. Use generous glue on both sides of each joint.
Build the corners carefully. At an inside corner, fit the strips to the real angle, not to 90 degrees. Read the angle with the angle finder and write it on the template ("CORNER 91.5°"). If the two legs will be separate stone pieces, build them as separate templates with the seam line marked. If the L will be one piece, build it as one rigid unit.
Handle the ends. Mark each end as a finished end (gets the edge profile), a wall end, or an appliance end. At a slide-in range, check the range manufacturer's required gap and mark it.
Locate the sink. Find the center of the sink base cabinet and mark a centerline across the template. For an undermount, place the manufacturer's cutout template on the frame or trace the actual sink upside down, then write the model number and the reveal. The reveal is how much of the sink rim shows past the stone edge: positive (rim visible, commonly about 1/8 inch), zero (flush), or negative (stone overhangs the bowl).
Mark faucet and accessory holes. Note the number of holes, their spacing (for example 8-inch widespread) and their distance from the back of the sink cutout or the wall. Check that a faucet handle will clear the backsplash and window sill.
Mark the cooktop. Take the cutout size from the appliance's installation manual, not from the old top, and mark the cooktop's centerline and distance from the front edge.
Mark seams. Draw the agreed seam lines and write "SEAM". Seams should avoid sink and cooktop cutouts and unsupported spans, and they should be where the customer has agreed to them. See seams.
Record the backsplash. Height, length, which ends are finished, and outlet and switch positions if the splash is tall enough to need cutouts.
Label everything (see the next section), then photograph each piece in place, every corner, the sink and cooktop areas, and the walls.
Get sign-off. Walk the customer through overhangs, seams and the sink position, and have them sign the template sheet or job form.
Lift it off carefully. Lift each piece from several points at once so the glue joints do not crack. Carry it flat or on edge, never by one corner.
How to mark and label a template
A template leaves the house and passes through several people's hands. Anything not written on it gets guessed at in the shop. Use the shop's standard marks everywhere so a programmer reads every template the same way.
Mark | Meaning |
|---|---|
FE or FIN | Finished edge, gets the profile |
W or WALL | Wall edge, sawn only |
Overhang value on the front strip | For example "OH 1-1/2" |
SEAM with a line | Agreed seam location |
CL | Centerline of sink, cooktop or faucet |
Sink model and reveal | For example "Model X, undermount, +1/8 reveal" |
Corner angle | Measured angle where not 90° |
R and a value | Radius at a corner, for example "R 1-1/2" on an outside corner |
TOP / THIS SIDE UP | Which face is up. A template flipped over produces a mirror-image piece. |
Arrow to wall | Which way the piece faces |
Job name, room, piece number, date, initials | So pieces can't be mixed up between jobs |
Write labels on the top face only, and write them large. Mixed-up labels cause the classic physical-template errors: a piece cut mirror-image, a finished edge left sawn, or a vanity top cut for the wrong bathroom.
Curves, bowed walls and awkward conditions
Bowed walls. Scribe rather than force a straight strip. Set the compass to the widest gap, run it along the wall with the pencil on the strip, then cut to the line.
Curves and radius islands. Rip narrow strips (1/2 to 3/4 inch) that bend smoothly, glue two or three layers together once they are bent to shape, and brace them back to the frame. For tight radii or free-form shapes, glue a solid luan or hardboard sheet in place and trace the curve onto it.
Columns, window returns and bump-outs. Build the strip around them and add two reference measurements to each feature, so the shop can check the shape.
Apron-front sinks, knee walls and other special cases are covered in templating tricky conditions.
What happens to the template in the shop
A physical template becomes stone in one of two ways.
Traced on the slab. The template is laid on the slab, positioned for the best part of the pattern, and traced. The saw operator cuts to the line. This is simple and lets the shop and customer see the exact vein placement on each piece, but it relies on the operator's accuracy and is slower than CNC cutting.
Digitized for the CNC. The template is turned into a CAD file, either with a camera-based digitizing system that photographs it against reference targets, on a digitizing table, or by measuring it and redrawing it in CAD. The file then goes through the same programming and nesting as a digital template. This adds about 20 to 60 minutes per job, and every transfer adds a little error. See DXF and CNC files.
Store and move templates flat, or on edge with support. A large template leaned against a wall for a couple of days, especially in a humid shop, can take a set and warp. Keep templates until the job is installed and signed off. They are your record if a fit question comes up.
How accurate is a physical template?
On site, a careful strip template holds about 1/16 inch. By the time it is traced or digitized and cut, the finished stone is typically within 1/16 to 1/8 inch. The errors add up along the way:
Error source | How it happens | Prevention |
|---|---|---|
Strip flex | Narrow or single strips bend when lifted | Proper strip width, cross-pieces every 12 to 18 in, diagonal braces |
Glue joint creep | Joints shift under load or in heat | Generous glue, let joints cool before lifting, keep templates out of hot trucks |
Racking in transport | Frame shifts into a parallelogram | Diagonal braces, flat transport |
Tracing and digitizing | A marker line is about 1/32 in wide, plus the digitizer's own error | Trace one consistent side of the line, check key dimensions after digitizing |
Assumed angles | Corners built at 90 degrees by eye | Measure and write every corner angle |
Wrong reference | Measured to tile, or to a cabinet that later moved | Template only on final cabinets, to the finished wall |
Most physical-template problems are not measuring errors. They are information errors: a missing label, the wrong sink model, a forgotten side splash or overhang note. That is why the checklist and labeling matter as much as the strips.
Physical vs digital templating
Physical strip template | Digital templating | |
|---|---|---|
Equipment cost | Under a few hundred dollars for tools | Roughly $10,000 to $30,000 or more for a professional system, plus software |
Materials per kitchen | $20 to $50 | None |
Time on site, standard kitchen | 45 to 90 minutes, up to 2 hours for complex jobs | About 20 to 60 minutes |
Shop time before CNC | 20 to 60 minutes to trace or digitize | Minutes of file cleanup |
Typical accuracy | About 1/16 in on site, 1/16 to 1/8 in in the finished piece | About 1/32 to 1/16 in |
Output | Physical pattern | CAD file (usually DXF) |
Tight spaces | Works anywhere | Can struggle without line of sight |
Storage | Bulky, can warp | A file |
Training | Learned by shadowing | Device training plus field practice |
Failure modes | Flex, warping, lost or mislabeled pieces | Calibration drift, battery, operator technique |
Digital usually wins in a shop with a CNC and steady volume, because it saves time at both ends and the file goes straight into programming and nesting. Physical makes sense for low-volume shops, shops without a CNC, backups, tight spaces, and as a layout aid on patterned slabs. Many shops use both. Device options are compared in digital templating tools.
Time and cost
Job | Typical on-site time |
|---|---|
Single vanity | 15 to 30 minutes |
Galley or straight-run kitchen | 30 to 60 minutes |
L or U kitchen with island | 60 to 90 minutes |
Complex kitchen with curves, many corners or an apron sink | Up to about 2 hours |
A dedicated templater can usually do 3 to 6 residential jobs a day. Travel between jobs, not measuring time, is often what limits that number.
Shops handle template fees in different ways. Many include templating in the fabricated price. Others charge a separate fee, commonly $75 to $300 for a kitchen depending on region and complexity, and often credit it toward the job. A return visit because the cabinets were not ready or the customer changed the design commonly costs $75 to $200 (2026 U.S. ranges). See installation and removal costs.
Common mistakes
Templating before the cabinets are final, or on unlevel cabinets
Assuming corners are 90 degrees
Guessing the sink cutout instead of using the actual sink or the manufacturer's template
Using the old top's cooktop hole instead of the new cooktop's spec
Forgetting side splashes, small returns and the finished ends
Missing or ambiguous labels, especially which side is up
Setting the overhang by eye instead of with a gauge block
Building large pieces without diagonal braces
Leaning templates against a wall in the shop for days
Leaving the house without photos and a customer sign-off
Training a new templater
Templating combines carpentry-style measuring with geometry and a lot of checking. Candidates with tile, cabinet or carpentry backgrounds pick it up fastest. Fraction arithmetic in sixteenths should be automatic. A new templater also needs to know how to check square with a 3-4-5 triangle, read a sink or cooktop spec sheet, and recognize an overhang or seam that needs support or a supervisor's decision.
Common shop practice is several weeks of shadowing, then leading simple jobs with a mentor checking the work. Many shops use 15 to 20 supervised jobs across different layouts before anyone templates alone, and the first solo jobs are straight vanities or galley kitchens. Shops that also use digital devices often train new hires on strips first, because building a physical template teaches what the numbers mean. See hiring and training.
Homeowner template kits
Some online stone sellers send homeowners kits of cardboard or plastic strips with connectors and instructions. They work for simple straight runs and vanities. They are risky for kitchens with inside corners, curves, cooktops or several seams. A careful homeowner kit is usually accurate to about 1/8 inch, and the most common error is an out-of-square corner, not a bad tape reading. Most local fabricators will not cut from a customer's template, or they charge to re-template. A shop that does accept one should re-check the key dimensions and corner angles and make clear in writing who pays if it does not fit.
Where software helps
Physical templates fail on missing information more than on bad measurements, and a strip frame can carry only so many notes. In Stonify, the templater's trip appears in the Logistics app with the job's files, and the templater uploads photos and documents from the site to the job. The countertop drawing works on a tablet, and sink and cooktop cutouts can show center lines and distances from the edges, so the office can redraw the template with the exact cutout positions for the shop floor. A template-review task can sit in the shop's workflow between templating and cutting, so nothing goes to the saw before someone has checked the template against the quote. Calendars can total templating square footage per day to plan templater capacity.
FAQ
What is the best material for countertop template strips? 1/8-inch luan is the most common: stiff lengthwise, light and easy to glue. MDF strips and corrugated plastic also work. Cardboard is cheap but flexes and swells in humidity, so it suits only small, simple pieces.
Should the template go tight to the wall or leave a gap? Tight to the actual wall, following any bow. The shop subtracts its standard install clearance when it cuts, so every template means the same thing.
Can I template over the old countertops? Only if the shop agrees and the old tops sit exactly where the new ones will. Usually the old tops come off first, because they hide the cabinet faces and can change the height.
How long should a shop keep physical templates? At least until the job is installed and signed off, and longer if storage allows. The template is the evidence if the fit is questioned.
Do I still need a template if I have the kitchen plans? Yes for stone. Plans show design intent, and cabinets are rarely installed exactly to plan. Plans are good for quoting and ordering material.
Is a physical template accurate enough for a mitered or waterfall edge? It can be, with care, but tight miters and long waterfall panels leave little room for error. Many shops template those with a digital device, or verify a physical template with extra measurements.
Related Articles
Digital countertop templating: how laser and probe systems work, how accurate they are and when they pay off
How digital countertop templating works, the main device types, real field accuracy, time per kitchen, cost and payback, and how to roll it out in a shop.
How to template tricky countertop conditions: out-of-square walls, inside corners, curves, apron sinks and outlets
Field methods for templating out-of-square walls, L and U corners, curves, apron-front sinks, knee walls, overhangs, outlets and appliances, plus site readiness and sign-offs.
Countertop template errors: the common ones, how to verify a template before cutting and how to reduce remakes
The template errors that cause most countertop remakes, a step-by-step template verification checklist, what automated and AI checks can do, and how to cut remakes.