Care & Maintenance
How to restore the shine on stone countertops: polishing, buffing and resurfacing
Why granite, marble and quartz go dull, how to tell film from wear, how to polish out haze and scratches yourself, and what professional resurfacing costs in 2026.
, CEO, Stonify
Short answer: Most "dull" stone countertops are not worn at all. They are coated with a film of soap, hard-water minerals or dried sealer, and a thorough clean with a stone-safe cleaner and a polishing cream brings the shine back for under $30. Real wear, such as scratches, etch marks or dull traffic paths, needs the surface re-abraded with diamond pads, working from coarse to fine grit. Light marks can be done by hand. Whole-kitchen work is a professional job at typically $3 to $8 per sq ft for polishing and $8 to $15 per sq ft for grinding and re-polishing (2026 U.S. ranges). Granite, quartzite and marble restore well. Engineered quartz, porcelain and laminate have much tighter limits.
Why a countertop looks dull
A polished surface is shiny because it is flat at a microscopic level, so light reflects off it in one direction like a mirror. Anything that roughens the surface or sits on top of it scatters the light and reads as dull. Find the cause before you buy anything.
Cause | What it looks like | Fix |
|---|---|---|
Soap or cleaner residue | Streaky, cloudy film, worse where you wipe most | Deep clean, then switch to a pH-neutral stone cleaner |
Hard-water deposits | White rings and spots, often around the faucet | Stone-safe hard-water remover and a plastic scraper |
Dried sealer | Hazy or blotchy film, sometimes sticky, right after sealing | Reactivate with fresh sealer and wipe hard, or the sealer maker's remover |
Wax, oil or "polish" buildup | Smeary look, fingerprints show, water does not bead normally | Strip with an alkaline stone stripper |
Fine scratches or swirl marks | Arcs or lines visible in raking light | Polishing cream for the lightest, diamond pads for deeper |
Etching (marble, limestone, some "quartzite") | Dull, lighter spots where acids touched | Polishing powder or re-honing. See marble etching and restoration |
Worn polish | General dullness in busy zones such as by the sink | Professional re-polish |
The wet test. Wet the dull spot with plain water. If the dullness nearly disappears while wet and comes back when dry, the surface itself is roughened (scratches, etching or worn polish), and only polishing will fix it. If the haze stays visible while wet, something is sitting on the surface, and cleaning or stripping will fix it.
Dark stones such as Absolute Black show every film and fingerprint. Many black "granites" are actually gabbro or diabase, dense rocks that show residue and fine scratches more than speckled granite.
The terms: cleaning, buffing, polishing, honing and resurfacing
People use these words loosely, and contractors price them very differently.
Cleaning removes what is on the surface. It changes nothing about the stone.
Buffing with a polishing cream or powder is a maintenance step. The cream fills and smooths micro-abrasions and adds reflectivity. It removes almost no stone and does not fix anything you can feel.
Polishing re-abrades the surface with a sequence of diamond grits, finishing fine enough (1,500 to 3,000 grit and up, plus compound) to reflect light like a mirror.
Honing follows the same process but stops at a medium grit, usually 400 to 800, for a matte or satin surface. See surface finishes.
Grinding starts with coarse grits (50 to 200) to remove deep scratches, chips and height differences at seams, then works up.
Resurfacing in the stone trade means grinding, honing and polishing the stone in place. Some companies use the same word for painting or coating a countertop, which is a different thing entirely. See painting and cosmetic updates.
Sealing is separate. A penetrating sealer slows staining. It does not add shine, and polishing strips it from the worked area. See sealing natural stone.
How grit sequences work
Every abrasive leaves scratches of its own size. Polishing is a series of steps where each finer grit removes the scratches the previous grit left, until the scratches are too small to scatter light. Skipping a grit leaves scratches the next pad cannot remove. They look fine under dim light and dull under good light.
Stage | Typical grits | What it does |
|---|---|---|
Grinding | 50 to 100 | Removes deep scratches, chips and seam lippage. Rarely needed at home |
Shaping | 200 to 400 | Removes moderate scratches and deep etches |
Honing | 400 to 800 | Matte to satin. The stopping point for honed finishes |
Polishing | 1,500 to 3,000 | Gloss begins and builds |
Final buff | Powder, cream or 6,000+ | Full gloss with almost no stone removed |
Stone is always worked wet. Water cools the pad, carries away slurry and keeps dust down.
Restoring shine by material
Material | Can it be polished in place? | Notes |
|---|---|---|
Granite (Mohs 6 to 7) | Yes, very well | The most forgiving. Rarely needs deep work |
Quartzite (Mohs about 7) | Yes | Hard on pads. Some slabs contain softer veins that polish differently |
Marble, limestone, travertine (Mohs 3 to 4) | Yes, easily | Scratches and etches easily, and over-polishes easily. See the marble article |
Engineered quartz | Limited | Heat-sensitive resin. Spot work often leaves a sheen mismatch |
Soapstone (roughly Mohs 1 to 3) | Yes, by sanding | Sandpaper and mineral oil, not diamond polishing |
Solid surface | Yes, by sanding | Sands out like a plastic. Easy for matte, harder for gloss |
Porcelain and sintered stone | No | Fired surface. Scratches that cut the glaze or print are permanent |
Laminate | No | The pattern is a printed sheet. Once worn through, replace |
Concrete | Yes, by a specialist | Re-grind, re-polish and reseal |
Wood | Yes | Sand and refinish. See wood countertop care |
Granite and quartzite
Granite is hard enough that everyday knives and pots rarely scratch it. Gray lines after dragging a pot are usually metal rubbed onto the stone, not scratches, and they wipe off with a cleaner. True scratches come from harder grit, ceramic bases, diamond rings or sand under a sliding appliance.
Most granite that looks tired needs a deep clean, a polishing cream and a reseal. Diamond work is for scratches you can feel and for sink zones where the polish has worn after many years.
Marble
Marble dulls mostly from etching, not wear, and its softness means it scratches and over-polishes easily. Grit sequences and DIY methods are covered in marble etching and restoration.
Engineered quartz
Engineered quartz is crushed quartz bound with polymer resin through its full thickness. It does not etch, so most dullness on quartz is film: hard water, soap, or cleaners and "polishes" that leave residue. Clean it with a pH-neutral cleaner or one the brand approves. For dried-on film, some brands list a soft cleanser such as Bar Keepers Friend, used briefly and rinsed. Never apply a stone sealer or wax to quartz. There is nothing for it to soak into, so it sits on top and hazes.
Scratches you can feel are harder. A professional can polish quartz with water-cooled diamond pads at low speed, the same way fabricators polish cut edges. The resin softens and discolors from roughly 300°F, though, so friction heat from a fast buffer can burn it, and a hand-polished spot often shows a different sheen from the machine-polished factory surface. Many repairers prefer to polish a whole piece rather than a spot. Heat scorch marks are usually permanent. Matte and honed quartz finishes should be cleaned, never polished, or they end up with shiny patches.
Resurfacing an entire quartz kitchen to a new finish is possible but runs roughly $400 to $800 or more, close to the cost of new pieces in some cases. Most owners live with minor wear. See quartz.
Soapstone and solid surface
Soapstone is soft. Scratches sand out with 120 to 220 grit sandpaper, followed by mineral oil to even the color. See soapstone.
Solid surface such as Corian is the same color all the way through. Wet-sand scratches with 220, then 320 and 400 grit, and finish with a gray or white abrasive pad for a matte look. Gloss finishes need finer grits and a polishing compound, and are usually a job for a certified refinisher. See solid surface.
DIY: bring back the shine on granite
This fixes film and light dullness on polished granite and quartzite. It takes about 90 minutes for an average kitchen and $20 to $60 in products.
Deep clean. Scrub with a pH-neutral stone cleaner and a soft pad. For old wax, oil or cleaner buildup, use an alkaline stone stripper made for the purpose, then rinse well.
Remove hard-water spots with a stone-safe hard-water remover and a plastic scraper. Do not use vinegar or lime removers. They strip sealer, and some granites contain calcite that etches.
Dry completely.
Test the sealer. Put a few drops of water in several spots, including by the sink. If they soak in and darken the stone within about 5 minutes, plan to reseal after polishing, not before.
Apply a granite polishing cream (Tenax Ager, MB-11 and StoneTech products are common). Work a small amount into a 1 to 2 sq ft section with a clean cloth or felt pad, in circles.
Buff to a shine with a second dry microfiber cloth. Move on in overlapping sections.
Reseal if the water test showed absorption. Apply a thin coat, let it dwell per the label, then wipe off every bit of excess before it turns tacky. Leftover sealer is the most common cause of new haze.
Work out of direct sun and on a cool surface, so products do not dry before you buff them.
DIY: remove light scratches from granite
Use the fingernail test first. If your nail does not catch, a polishing cream or a 3,000-grit hand pad may be enough. If it catches slightly, start with diamond hand pads at 400 grit. If it catches clearly, start at 200 grit or call a pro.
Wet the area with a spray bottle.
Work the starting grit in small overlapping strokes for 2 to 3 minutes, keeping it wet.
Wipe and inspect in raking light. Move up only when the scratch is gone and the new scratch pattern is even.
Step through 800, 1,500 and 3,000 grit, feathering a few inches beyond the scratch each time.
Finish with polishing cream or compound and buff dry.
Reseal the worked area once dry.
Diamond hand pads cost about $5 to $20 each, or $30 to $80 for a set. A variable-speed wet polisher costs $80 to $200 to buy or $40 to $80 a day to rent. Never run an angle grinder dry on stone. It heats the surface, glazes the pads and throws dust.
When to hire a professional
Call a restoration contractor for scratches you can feel over a large area, a dull sink zone that polishing cream does not fix, uneven seams, many etches on marble, or a change of finish. A pro uses a variable-speed or planetary polisher with water feed, works through the full grit sequence, and reseals.
What professional polishing and resurfacing cost
Typical 2026 U.S. ranges. High-cost metros often run 30 to 50% higher.
Service | Typical price |
|---|---|
Polish only (restore gloss, light scratches) | $3 to $8 per sq ft |
Honing to a matte finish | $5 to $12 per sq ft |
Grind, hone and re-polish (deep scratches, lippage, chips) | $8 to $15 per sq ft |
Heavily damaged stone, billed hourly | $75 to $150 per hour |
Complex edge profiles (ogee, dupont) | Add about $2 to $5 per linear ft |
Minimum charge | $150 to $300 |
Quartz polish of a whole top | $200 to $500+, results vary |
Solid surface refinish | About $4 to $8 per sq ft |
Worked example. A 45 sq ft granite kitchen has a dull, scratched zone around the sink and fine scratches on the island. A polish at $3 to $8 per sq ft comes to $135 to $360, which most contractors would bill at their minimum or above. If the island scratches need grinding, $8 to $15 per sq ft brings the job to about $360 to $675. New granite for the same kitchen typically costs a few thousand dollars, so restoration is the far cheaper path for sound stone.
There is no national license for stone restoration, and price alone does not show skill. Get two or three written estimates. Ask which grits they use and in what order, whether they work wet, how they protect cabinets and floors, and whether they will do a test area. Be wary of a quote around $1 per sq ft for a "polish," which usually means a quick buff with a coating. The Natural Stone Institute lists member restoration contractors.
How long a professional polish lasts
Stone polishing removes stone. It does not add a coating, so the result lasts until the surface wears again. On granite that is often a decade or more, and busy sink zones dull first. Keeping the sealer up and cleaning with pH-neutral products stretches it. Marble in a busy kitchen needs work more often.
Changing the finish
A contractor can change a finish in place:
Polished to honed: stop the grit sequence at 400 or 800. This is a common request for marble kitchens, because etches show less on a matte surface. Honed stone is slightly more open, so reseal and expect fingerprints and oil marks to show a bit more.
Honed to polished: work up through every grit to 3,000 and compound. More labor than the reverse.
Leathered or brushed: these textured finishes are made with brushes in the shop and are hard to reproduce in place. Clean them. Do not polish them, or you flatten the texture in patches.
Dust and silica
Granite and quartzite contain crystalline silica, and engineered quartz is over 90% quartz. Grinding or sanding them dry releases respirable silica dust, which causes silicosis. Wet hand-pad work at home produces little dust. Power tools must be run wet or with a shroud and HEPA vacuum (in California, work on engineered stone must be done wet). Professionals working in homes fall under OSHA's construction silica standard (29 CFR 1926.1153): a permissible exposure limit of 50 µg/m³ as an 8-hour average and an action level of 25 µg/m³. A contractor who grinds dry in your kitchen is a red flag. See silica and silicosis.
Mistakes that make it worse
Olive oil, coconut oil or furniture polish for shine. Oils soak into natural stone, darken it and go rancid. Silicone polishes block future sealing.
Car wax or floor finish. It coats instead of polishing, traps dirt and yellows.
Vinegar, lemon or "natural" citrus cleaners. They strip sealer and etch calcite-bearing stone.
Sealing over haze. More sealer on top of scale or residue locks the problem in. Clean first.
Sealer or wax on quartz. It has nothing to soak into and leaves a film.
Polishing powder or cream on honed or leathered stone. It creates shiny patches.
Green scouring pads and Magic Erasers on polished stone. They are abrasive and dull the gloss over time.
Skipping grits or working dry. Both leave visible scratch patterns or burn marks.
For fabricators: restoration questions from your customers
Most "my granite lost its shine" calls are film. Walk the customer through the wet test on the phone. It often saves a truck roll and earns trust.
Prevent sealer haze at install. Seal only fully dry stone and wipe off all excess within the dwell time. Haze in the first week is almost always an application problem.
Hand over a care sheet that names the cleaner and sealer you used and lists products to avoid. See cleaning by material.
Be honest about quartz. Customers expect stone-like repairability. Explain that heat marks are permanent and scratch polishing has limits.
Price restoration per sq ft with a minimum that covers the drive and setup, and add edge footage for profiled edges.
FAQ
Can I use a granite "polish and seal" spray instead of real polishing? For routine upkeep, yes. These combination products add a little shine and a little sealer protection. They do not remove scratches or etching.
Can I polish just one scratched spot? On granite, usually yes, if you feather the work a few inches past the scratch. On marble, quartz and honed stone, spot work often leaves a patch with a different sheen, so pros tend to work the whole piece.
Will polishing remove stains? No. Stains are color that soaked into the stone and need a poultice. Remove stains first, then polish, then seal. See stain removal.
Can porcelain or sintered stone be re-polished? Not in any practical way. Metal marks and residue clean off. Real scratches through the fired surface stay.
How often should I use a granite polishing cream? A few times a year is plenty for most kitchens. Daily cleaning with a pH-neutral cleaner and a dry buff with a microfiber cloth does most of the work.
Related Articles
Marble etching: what it is, how to fix it and when to call a restorer
Why acids etch marble, how to tell an etch from a stain, how to polish or re-hone etch marks yourself, and what professional marble restoration costs in 2026.
How to clean countertops by material: granite, marble, quartz, quartzite, soapstone and porcelain
The daily cleaning routine that works on every countertop, what each material can't take, safe ways to disinfect, and why vinegar, bleach and Clorox wipes cause trouble.
Sealing natural stone countertops: which stones need it, how often and how to do it
Which countertops need sealing, how the water test works, penetrating vs topical vs color-enhancing sealers, step-by-step sealing, why sealers fail and what resealing costs.