Equipment

What Are the Best Suction Cups for Stone CNC Machines? (2027)

The best suction cups and vacuum pods for stone CNC machines: Blick, BVC, Schmalz and Amastone compared, plus setup tips.

Stonify Industry Knowledge · November 2026

Suction cups, also called vacuum pods, are the only thing holding a 200-pound countertop still while a CNC spindle works on it. When they hold, nobody thinks about them. When one leaks or sits a fraction of a millimeter high, the result is a wavy edge, a broken piece or a crashed tool.

The best suction cups are flat to a tight tolerance, hold strongly, don’t mark the stone and match your machine. Below we explain what matters, then compare the brands fabricators use most.

What Makes a Good CNC Suction Cup

  • Height tolerance. Every cup on the table must be the same height. Small differences show up as lines in the edge polish.

  • Holding power. Larger vacuum channels and good seals hold heavy or narrow pieces securely.

  • Non-marking rubber. Top pads and seals should not stain or scratch polished stone.

  • Shapes. Rectangular, square, round and corner cups, plus narrow cups for strips and special cups for vanity sinks.

  • Compatibility. Height and vacuum connection must match your CNC table.

  • Replaceable pads. Top pads wear and get cut. Replaceable pads cost less than new cups.

Quick Answer: Who to Look At

If you need…

Look at

The widest US-made selection

Blick Industries

Cups you can route into and keep using

Better Vacuum Cups (BVC)

Modular vacuum blocks from an automation specialist

Schmalz VCBL-GL

Certified-tolerance pods for any CNC brand

Amastone

An exact match to your machine

Your CNC maker’s OEM cups

The Brands

1. Blick Industries

Blick, of Laguna Beach, California, has supplied vacuum workholding for CNC machines for more than 25 years, with every product designed and made in the USA. It offers more than 40 cup shapes, retractable cups that lower sink cutouts automatically, and a vanity sink kit. Its enhanced top pad, with a larger vacuum channel for more holding power, won a Best of StonExpo award in 2021. Blick replaces a pad at no charge if it delaminates for reasons other than damage.

Best for: US shops that want the broadest range and strong support.

2. Better Vacuum Cups (BVC)

BVC has made vacuum cups for stone, glass and wood CNC routers for over 20 years. Its cups can be routed into and still used, and come in standard heights of 105, 150 and 200 mm, including the SS100 cup.

Best for: shops that often cut close to or into their cups.

3. Schmalz VCBL-GL

German vacuum specialist Schmalz released a new generation of its VCBL-GL vacuum blocks in late 2025, with modular construction, improved sealing and more shapes for stone and glass CNC work.

Best for: shops that want a modular system from a global vacuum automation brand.

4. Amastone CNC Vacuum Pods

Amastone sells round, square, rectangular and corner pods compatible with any stone CNC brand, certified to a height tolerance of ±0.02 mm, with stain-resistant rubber.

Best for: matching cup height to an existing set on any machine.

Side-by-side

Brand

Based in

Shapes

Standout feature

Blick Industries

USA

40+

Retractable cups, enhanced top pad, pad replacement policy

Better Vacuum Cups

USA

Pod and rail styles

Can be routed into; 105 / 150 / 200 mm heights

Schmalz VCBL-GL

Germany

Modular variants

Modular design, upgraded sealing

Amastone

Italy

Round, square, rectangular, corner

±0.02 mm certified tolerance

Setup Tips That Prevent Broken Pieces

  1. Use one set. Don’t mix cups of different brands or ages on the same piece. Blick advises using all its cups together for the same reason.

  2. Clean the table and seals before every setup. Slurry under a cup changes its height.

  3. Support narrow pieces with narrow cups, and never leave an edge hanging far past the last cup.

  4. Check the vacuum gauge before starting. A slow leak becomes a moving piece.

  5. Store cups on their sides, not stacked on their pads.

  6. Replace worn pads instead of working around them.

Dynamic Stone Tools publishes a detailed guide to CNC vacuum pod setup and selection, and stocks CNC tools and accessories at dynamicstonetools.net.

Dynamic Stone Tools is a Stonify technology partner.

Frequently Asked Questions

How Many Suction Cups Do I Need?

Enough to support every piece on the table with no long unsupported spans. Most shops keep a mix of large rectangular cups, narrow cups for strips and corner cups, plus a few spares.

Why Did My Piece Move on the CNC?

Common causes are a dirty seal, a worn pad, too few cups under a narrow piece, or a vacuum leak. Check the gauge and the seals first.

Can I Use Different Height Cups Together?

No. All cups under one piece must be the same height, or the piece will rock and the edge will show lines.

How Often Should Suction Cup Pads Be Replaced?

When they are cut, hardened, delaminating or no longer hold vacuum. Inspect them weekly in a production shop.

The Bottom Line

Blick Industries is the benchmark for US stone shops, with BVC, Schmalz and Amastone as strong alternatives. Whichever you choose, keep one matched set, keep it clean and replace pads early. For the machines these cups sit on, see our guide to the best CNC polishing machines.

Ready to Run a Smarter Stone Operation?

Book a demo to see how Stonify can reduce costs at your shop.

Ready to Run a Smarter Stone Operation?

Book a demo to see how Stonify can reduce costs at your shop.