Technology

How to Quote a Backsplash From a Drawing

Work through a kitchen elevation, calculate short-splash length and panel area, then check what changes when the customer raises the panel behind the range.

A customer likes the four-inch backsplash on your kitchen quote but wants stone up to the hood behind the range. To price the change, mark where the short splash stops, draw the taller panel as its own piece, and check the units your shop bills for each. The wall can stay exactly the same length while the square footage and the work you owe the customer change.

Start With the Wall the Customer Will See

A countertop plan gives you a view from above. For the backsplash, sketch the same wall as if you were standing in front of it. Label the left end, the right end, the range opening, and any return onto another wall. Give each section a name that will still mean something to the installer. “Range panel” and “coffee wall” are easier to trace on a quote than “Piece 2” and “Piece 3.”

Write down which dimensions came from the customer or cabinet plan and which your shop has verified. A drawing can be accurate enough to price an option before it is ready for fabrication. If the bottom of the hood determines the final panel height, identify who will confirm that dimension and when. Keep that open question visible on the estimate you send.

Work One Elevation by Hand

Here is a fictional kitchen you can use to test backsplash drawing software. A straight wall is 120 inches long. A 36-inch-wide range panel occupies the middle. The other 84 inches get a four-inch stone splash. Assume a rectangular range panel, 30 inches high. Leave returns, seams, waste, tax, and install charges out of this first calculation so you can see what the drawing contributes.

  • Short splash on the left and right combined measures 84 inches, or 7 linear feet.

  • At four inches high, those two short pieces have 336 square inches of face area, or about 2.33 square feet.

  • The range panel measures 36 × 30 inches. Its face area is 1,080 square inches, or 7.50 square feet.

  • Combined face area is about 9.83 square feet. The short splash ends at each side of the panel.

Suppose your shop sells standard four-inch splash by the linear foot and full-height panels by the square foot. For this example, the two billable quantities are 7 linear feet and 7.50 square feet. The 9.83-square-foot figure is a check on the geometry. Adding it as another material charge would bill part of the work twice. If your shop prices from whole slabs, use the face area to check the drawing and use your slab layout to determine material requirements.

Change One Dimension and Follow the Difference

Now the customer asks for a 36-inch-high range panel. On the drawing, keep the width at 36 inches and change the height from 30 to 36. The revised panel is 9 square feet. Your expected change is 1.50 square feet, and the short splash still measures 7 linear feet. If the price of the short splash moves, inspect its endpoints. If the material line still says 7.50 square feet, the estimator may be looking at the previous quote.

Check one more detail before accepting the new price. Which panel edges are exposed? A taller piece can add finish work on an exposed side. It makes no such addition along an edge your shop has agreed to leave unfinished. Mark the finish on the drawing and use the shop’s own add-on pricing rules. Two estimates with identical panel area can legitimately carry different edge charges.

Spell Out What the Price Includes

If the elevation shows two outlets, give the estimator two separate questions. How many openings are included in this price? Who will verify their final locations? A count can support an estimate while the final positions are still open. Write the allowance in the quote and record the field check with the job. Apply your shop’s own opening and cutout rules when calculating the charge.

Read the revised scope as if you were the customer. “Seven linear feet of four-inch splash plus one 36-by-36-inch range panel, with two outlet openings allowed” gives someone a fair chance to catch a misunderstanding. Add the material, finish, installation scope, and any dimensions awaiting verification. Save the approved revision where the office and shop can identify it. The countertop drawing revision log gives you a way to record the change and the people who need it.

Try the Same Change in Stonify

Stonify Drawing and Slab Layout connects piece measurements with quote lines and tracks configured services such as backsplashes, edges, and cutouts. When a drawing and quote differ, the estimator can review missing lines and quantity changes. That matters on this job because a six-inch change belongs on the range panel and can leave most of the original quote intact.

Bring a marked-up elevation and one of your pricing rules to a Stonify demo. Ask the estimator to enter the first version, raise the panel, and show you the two quotes side by side. You should be able to point to the extra 1.50 square feet, explain any edge charge, and show the customer why the seven feet of short splash stayed the same.

Ready to Run a Smarter Stone Operation?

Book a demo to see how Stonify can reduce costs at your shop.

Ready to Run a Smarter Stone Operation?

Book a demo to see how Stonify can reduce costs at your shop.